FISHER定位器i2P-100技術參數
Input Signal | Available as standard with 4-20 mA. User configurable by dip switch for split ranging, see table below. |
Output Signal | Available as standard 0.2 to 1.0 bar (3 to 15 psig), 0.4 to 2.0 bar (6 to 30 psig), or 0.14 to 2.3 bar (2 to 33 psig). User configurable by dip switch selection and zero and span potentiometer adjustment, see table below. |
Equivalent Circuit | The i2P-100 equivalent circuit is a series circuit consisting of a constant voltage drop (battery) of approximately 4 VDC and a total resistance of 40 ohms. Input is shunted by two 6.8 V zener diodes . |
Supply Pressure(1) | |
Recommended: | 0.34 bar (5 psi) higher than upper range limit of output signal |
Maximum: | 3.4 bar (50 psig) |
Medium: | Air or Non-Corrosive Natural Gas |
Maximum Steady-State Flow Rate(2)(3) | Refer to tables 2 and 3 |
Maximum Output Air Capacity(3) | 8.04 m3/hr (300 scfh) at 1.4 bar (20 psig) supply pressure |
Performance(4) | |
Reference Accuracy: | ±1.0% of full scale output span; includes combined effects of hysteresis, linearity, and deadband |
Independent Linearity: | ±0.5% of full scale output span |
Hysteresis: | 0.4% of full scale output span |
Frequency Response: | Gain is attenuated 3 dB at 3 Hz with transducer output signal piped to a typical instrument input |
Temperature Effect: | ±0.14% per degrees Celsius (0.075 per degrees Fahrenheit) of span |
Supply Pressure Effect: | 0.2% of full scale output span per psi supply pressure change) |
Vibration Effect: | Less than 1% of full scale output span when tested to ISA S75.13 |
Electromagnetic Compatibility | |
Meets EN 61326-1:2013 | Immunity—Industrial locations per Table 2 of EN 61326-1 Standard. Performance is shown in table 1 below. |
Emissions—Class A | ISM equipment rating: Group 1, Class A |
Operating Ambient Temperature Limits(1) | -40 to 85C (-40 to +185F) |
Electrical Seal | Single sealed device per ANSI/ISA 12.27.01 |
FISHER定位器i2P-100產品介紹
The Fisher i2P-100 electro-pneumatic transducer, uses a converter module that converts a milliampere input to a proportional pressure output. Both the current input and pressure output range are user-configurable in the field. The converter module uses small parts of minimum mass, which are balanced symmetrically around a pivot point at the center of the mass. This balanced arrangement results in a high performance instrument that reduces sensitivity to vibration.
An integral pneumatic relay provides the high capacity necessary to drive pneumatic control valve/actuator assemblies without additional boosters or positioners. The transducer also provides stable, accurate operation when its output is transmitted to small volume chambers, such as a pneumatic positioner or other pneumatic instrument. Reduced sensitivity to vibration, combined with high capacity and first order lag characteristics, make the i2P-100 transducer suitable for direct mounting on control valve/actuator combinations.
Features
Approved for use with Natural Gas—The i2P-100 is approved for use with natural gas as the pneumatic supply.
Low Pneumatic Supply Consumption—The transducer has low pneumatic supply consumption which lowers operating costs. Maximum steady state consumption is less than the 6 SCFH requirement set for the oil and gas industry by the US Environmental Protection Agency (New Source Performance Standards Subpart OOOO, EPA-HQ-QAR-2010-0505).
Single Sealed Device— The i2P-100 has been tested in accordance with ANSI/ISA Standard 12.27.01 (Requirements for Process Sealing Between Electrical Systems and Flammable or Combustible Process Fluids) as a single sealed device.
High Output Capability and Rangeability— The integral output relay volume of the transducer is adequate to drive valve/actuator combinations without requiring a positioner or volume booster. Selectable user field-configurable dip switch setting for output range of 0.14 to 2.3 bar (2 to 33 psi).
Split Range—Selectable user field-configurable two-way split range, using either half of the standard input signal.
Corrosion Resistant—Separate housing compartments isolate the electronics from the pneumatic process. The electronics module is encased in a rugged plastic shell which helps to prevent damage to the electronics. The printed wiring board and dip switches are conformal coated to help prevent corrosion. Converter module coils have corrosion resistant coating and all flexures are gold plated to provide protection from hostile environments.
Tolerant of Dirty Supply Medium—Free-flow pilot stage design and large internal air passages provide excellent tolerance to dirty pneumatic supply, by reducing the effects of contaminant buildup and erosion. The removable primary orifice and replaceable 5 micrometer filter are easy to remove for service and maintenance.
Fisher i2P-100電動氣動傳感器使用轉換器模塊，該轉換器模塊將毫安輸入轉換為比例壓力輸出。電流輸入范圍和壓力輸出范圍均可在現場由用戶配置。轉換器模塊使用最小質量的小零件，這些零件圍繞質量中心的樞軸點對稱平衡。這種平衡的布置導致了高性能的儀器，降低了對振動的敏感性。
集成的氣動繼電器可提供驅動氣動控制閥/執行器組件所需的高容量，而無需額外的增壓器或定位器。當傳感器的輸出傳輸?shù)叫◇w積的腔室（例如氣動定位器或其他氣動儀器）時，該傳感器還可以提供穩定，準確的操作。降低的振動敏感性，加上高容量和一階滯后特性，使i2P-100傳感器適合直接安裝在控制閥/執行器組合上。
特征
允許與天然氣一起使用-i2P-100被批準與天然氣一起用作氣動供應。
氣動耗氣量低-變送器的氣動耗氣量低，從而降低了運營成本。最大穩態消耗量小于美國環境保護局為石油和天然氣行業設定的6 SCFH要求（新源性能標準子部分OOOO，EPAHQQAR20100505）。
單一密封設備— i2P-100已根據ANSI / ISA標準12.27.01（電氣系統與易燃或可燃過程流體之間的過程密封要求）進行測試，作為單一密封設備。
高輸出能力和可調范圍—傳感器的整體輸出繼電器體積足以驅動閥門/執行器組合，而無需定位器或體積增強器?？蛇x的用戶現場可配置撥碼開關設置，輸出范圍為0.14至2.3 bar（2至33 psi）。
分割范圍-使用標準輸入信號的一半，可選擇用戶現場配置的雙向分割范圍。
耐腐蝕—分開的外殼將電子設備與氣動過程隔離開來。電子模塊裝在堅固的塑料外殼中，有助于防止損壞電子模塊。印刷線路板和DIP開關都經過保形涂層處理，有助于防止腐蝕。換流器模塊線圈具有耐腐蝕涂層，所有撓性件均鍍金，以提供免受惡劣環境的保護。
耐臟供應介質-自由流動的先導級設計和較大的內部空氣通道可通過減少污染物積聚和腐蝕的影響而對較臟的氣動供應提供出色的耐受性?？刹鹦兜闹鞴?jié)流孔和可更換的5微米過濾器易于拆卸，以進行維護和保養。
FISHER定位器其他常見型號：
FISHER i2P-100
FISHER Locator NEW + ORIGINAL+ ONE YEAR WARRANTY
愛澤工業成立于2010年，定位于向先進制造工業提供高端制造技術和設備。代理經營世界先進的電氣自動化、機械與傳動、流體控制、儀器儀表、工具等產品。作為電氣，液壓以及氣動解決方案的合作伙伴，我們利用我們的全球協作團隊，為客戶提供先進解決方案，市場知識以及相關增值服務來幫助優化客戶的工作效率，提高可靠性和安全性，致力于成為工業產品和解決方案的優質渠道。
如果有任何關于FISHER定位器i2P-100的疑問，請隨時與我們溝通（021-31006702）。我們將盡全力解決您的問題。
If you have any question for FISHER products, please feel free to dial 0086-21-3100 6702/ send request email to sales@ize-industries.com / browse our website:jjxdch.cn.
FISHER定位器i2P-100產品參數
