亚洲日韩精品无码一区二区三区,日韩精品无码一区二区三区久久久 ,国产高清乱理伦片中文,无码精品久久久天天影视

IZE學院 訂單查詢

0086-21-31006702 聯系我們 關于我們 賬號注冊及登錄EN
您當前的位置: 首頁 >> 產品中心 >> 液壓 >> 液壓閥 >> 液壓閥 >> SUN HYDRAULICS

SUN HYDRAULICS

請注意:照片可能并不是實際產品,具體請參閱標題和產品規格及所有細節描述。
產品品牌:
型號:PPDBLNN
SUN閥PPDBLNN
預估貨期:
關  鍵  詞:SUN閥PPDBLNNPPDBLNN/APPPDBLNN/LHPPDBLAVPPDBLAV
相似產品:
是否有問題?聯系我們工作人員
  郵件聯系

SUN閥PPDBLNN技術參數

Technical Data


Cavity

T-11A

Series

1

Capacity

10 gpm

Maximum Operating Pressure

5000 psi

Factory Pressure Settings Established at

blocked control port (dead headed)

Control Pilot Flow

7 - 10 in3/min.

Adjustment - No. of CW Turns from Min. to Max. setting

5

Valve Hex Size

7/8 in.

Valve Installation Torque

30 - 35 lbf ft

Adjustment Screw Internal Hex Size

5/32 in.

Locknut Hex Size

9/16 in.

Locknut Torque

80 - 90 lbf in.

Model Weight

0.33 lb.

Seal kit - Cartridge

Buna: 990011007

Seal kit - Cartridge

EPDM: 990011014

Seal kit - Cartridge

Polyurethane: 990011002

Seal kit - Cartridge

Viton: 990011006

愛澤工業(ize-industries)并不是本網站所列所有產品的授權代理商或經銷商。 本網站使用的所有產品名稱,商標,品牌等均屬于各自品牌廠家所有。 本網站在產品或圖片描述中,出現具有這些名稱,商標,品牌等信息的產品僅用于識別目的,并非旨在表明任何與持有者的從屬及授權關系。

SUN閥PPDBLNN產品介紹

SUN閥PPDBLNN 愛澤工業 ize-industries (2).png 

 

先導式減壓/泄壓閥將入口(端口 2)處的高主壓力降低到端口 1 處的恒定減壓,并具有從端口 1 到油箱(端口 3)的全流量泄壓功能。

 

? 從減壓(端口 1)到入口(端口 2)的完全反向流動可能會導致主閥芯關閉。如果回路中需要反向自由流動,請考慮在回路中添加單獨的止回閥。

? 如果先導流量消耗至關重要,請考慮使用直接作用式減壓/泄壓閥。

? 建議的最大入口壓力由調節范圍決定。范圍 D、E、N 和 Q 的測試最大入口和減壓之間的壓差為 2000 psi (140 bar)。范圍 A、B 和 H 的測試最大入口和減壓之間的壓差為 3000 psi (210 bar)。范圍 C 和 W 的測試最大入口壓力為 5000 psi (350 bar)。

? 先導式閥門具有異常平坦的壓力/流量特性,非常穩定,滯后性低。

? 端口 3 處的壓力以 1:1 的比例直接添加到閥門設置中,并且不應超過 5000 psi (350 bar)。

? 先導式減壓閥、減壓/泄壓閥本質上不是快速作用閥。為了獲得卓越的動態響應,請考慮直接作用閥。

? 可以指定 W 和 Y 控件(如適用),無論是否指定特殊設置。當未指定特殊設置時,可以使用 W 或 Y 控件在整個范圍內調節閥門。當指定特殊設置時,此設置代表閥門的最大設置。

? 配置有 EPDM 密封件的閥芯用于磷酸酯流體系統。接觸石油基流體、油脂和潤滑劑會損壞密封件。

? 所有三端口減壓和減壓/泄壓閥芯在物理上都是可互換的(即,對于給定的框架尺寸,相同的流路、相同的腔體)??紤]安裝配置時,有時建議將全容量回流管線(端口 3)與減徑/泄壓閥筒一起使用。

? 采用 Sun 浮動式結構,以更大限度地減少由于安裝扭矩過大和/或腔體/閥筒加工變化而導致內部零件卡住的可能性。

 

Pilot-operated, pressure reducing/relieving valves reduce a high primary pressure at the inlet (port 2) to a constant reduced pressure at port 1, with a full-flow relief function from port 1 to tank (port 3).

 

? Full reverse flow from reduced pressure (port 1) to inlet (port 2) may cause the main spool to close. If reverse free flow is required in the circuit, consider adding a separate check valve to the circuit.

? If pilot flow consumption is critical, consider using direct acting reducing/relieving valves.

? Recommended maximum inlet pressure is determined by the adjustment range. Ranges D, E, N, and Q are tested with a 2000 psi (140 bar) maximum differential between inlet and reduced pressure. Ranges A, B, and H are tested with a 3000 psi (210 bar) maximum differential between inlet and reduced pressure. Ranges C and W are tested with 5000 psi (350 bar) of inlet pressure.

? Pilot operated valves exhibit exceptionally flat pressure/flow characteristics, are very stable and have low hysteresis.

? Pressure at port 3 is directly additive to the valve setting at a 1:1 ratio and should not exceed 5000 psi (350 bar).

? Pilot operated reducing, reducing/relieving valves by nature are not fast acting valves. For superior dynamic response, consider direct acting valves.

? W and Y controls (where applicable) can be specified with or without a special setting. When no special setting is specified, the valve is adjustable throughout its full range using the W or Y control. When a special setting is specified, this setting represents the maximum setting of the valve.

? Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.

? All three-port pressure reducing and reducing/relieving cartridges are physically interchangeable (i.e. same flow path, same cavity for a given frame size). When considering mounting configurations, it is sometimes recommended that a full capacity return line (port 3) be used with reducing/relieving cartridges.

? Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

 

SUN閥PPDB系列其他常用型號:

SUN PPDBLNN

SUN PPDBLNN/AP

SUN PPDBLNN/LH

SUN PPDBLAV

SUN PPDBLAV/AP

SUN PPDBLAV/LH

SUN PPDBLWV

SUN PPDBLWV/AP

SUN PPDBLWV/LH

 

SUN VALVE NEW + ORIGINAL+ ONE YEAR WARRANTY

 

愛澤工業成立于2010年,定位于向制造工業提供高端制造技術和設備。代理經營世界優質的電氣自動化、機械與傳動、流體控制、儀器儀表、工具等產品。作為電氣,液壓以及氣動解決方案的合作伙伴,我們利用我們的全球協作團隊,為客戶提供先進解決方案,市場知識以及相關增值服務來幫助優化客戶的工作效率,提高可靠性和安全性,致力于成為工業產品和解決方案的優質渠道。

 

如果有任何關于SUN閥PPDBLNN的疑問,請隨時與我們溝通(021-31006702)。我們將盡全力解決您的問題。

 

If you have any question for SUN products, please feel free to dial 0086-21-3100 6702/ send request email to sales@ize-industries.com / browse our website:jjxdch.cn.


SUN閥PPDBLNN技術參數介紹

免責聲明:本網站的布局,設計和編輯版權歸?上海愛澤工業設備有限公司(簡稱ize-industries)所有,保留所有相關權利。 Ize-industries銷售工業領域的全新產品,庫存產品,并不斷開發渠道購買此類產品。 本網站未經所有制造商或商標授權或批準。ize-industries不是所有制造商的授權經銷商,附屬公司或代表處。除非另有明確說明,否則此處出現的指定商標,品牌名稱和品牌均為其各自所有者的財產。