B+S V型圈TWVS01900-N6T50產品參數
Specification | |
Installation Dimensions: | |
For shaft diameter, d1 | 58 - 63 mm |
Inside diameter d | 54.0 mm |
Height of cross section c | 5.0 mm |
Dimensions A | 9.5 mm |
Free Width, B | 13.0 mm |
Maximum, d2 | d1 + 2 mm |
Minimum, d3 | d1 + 15 mm |
Fitted width, B1 | 11.0 ±1.0 mm |
Material Properties: | |
Maximum Operating Temperature | 100.0 °C |
Minimum Operating Temperature | -40 °C |
Hardness Nominal | 60.0 |
Hardness Tolerance | +/- 5 |
Hardness Unit | Shore A |
Color | Black |
Seal Capabilities: | |
Min. Temperature | -40.0 °C |
Max. Temperature | 80.0 °C |
Speed max. | 10.0 m/s |
Pressure max. | 0.0 MPa |
B+S V型圈產品介紹
V型圈是完美的密封件，可防止污垢，灰塵，水或這些介質的結合進入，同時又能有效保留油脂。
VRing具有獨特的設計和性能，可用于多種軸承類型。它也可以用作輔助密封件，以保護在惡劣環境下無法正常工作的主要密封件。
V型圈通常會拉伸并直接安裝在軸上，并通過橡膠體的固有張力將其固定在適當?shù)奈恢?。它與軸一起旋轉，并垂直于軸軸向抵靠固定的相對端面進行軸向密封。相對表面可以是軸承或墊圈，沖壓件，軸承箱的側壁，甚至是油封的金屬外殼。密封唇是柔性的，并且僅對相對面施加相對輕的接觸壓力，但仍然足以保持密封功能。較低的接觸壓力（隨安裝寬度而變化）使密封件在許多應用中干燥運行。由于離心力的影響，唇的接觸壓力隨速度增加而降低。這意味著將摩擦損失和熱量保持在最低水平，從而獲得出色的磨損特性并延長了密封壽命。一旦克服了分離摩擦，摩擦就會穩定減小，直到10-15 m / s范圍內，然后迅速減小。在15 -20 m / s的范圍內，摩擦減小到零。然后，VRing用作間隙密封和導流板。即使存在一定程度的跳動，偏心和軸未對準，柔性的唇緣和鉸鏈也可以使VRing發揮作用。 V型圈完全由橡膠制成，無織物或鈑金加固。因此，它們特別易于安裝?？梢岳霽型圈，并根據尺寸將其安裝在法蘭，皮帶輪和軸承箱上，而無需進行昂貴的拆卸。
V型環A型是最常見的，適用于各種直徑的軸。如果需要非常牢固地握住軸，則建議使用S型V形圈，但是這種情況只能達到200 mm的軸直徑。
The V-Ring is the perfect seal to prevent the ingress of dirt, dust, water or combinations of these media while positively retaining grease.
With its unique design and performance the VRing can be used with a wide range of bearing types. It can also be used as a secondary seal to protect primary seals that do not perform well in hostile environments.
The V-Ring is normally stretched and mounted directly on the shaft, where it is held in position by the inherent tension of the rubber body. It rotates with the shaft and seals axially against a stationary counter face, perpendicular to the shaft. The counter face can be the side wall of a bearing or a washer, stamping, bearing housing,or even the metal case of an oil seal. The sealing lip is flexible and applies only a relatively light contact pressure against the counter-face and yet is still sufficient to maintain the sealing function. The low contact pressure (that varies with the fitted width) allows the seal to run dry in many applications. Due to influence of the centrifugal force, the contact pressure of the lip decreases with increased speed. This means that frictional losses and heat are kept to a minimum, resulting in excellent wear characteristics and extended seal life. Once breakaway friction is overcome, the friction reduces steadily until around the 10 - 15 m/s range, when it reduces quite quickly. In the 15 -20 m/s range the friction reduces to zero. The VRing then serves as a clearance seal and deflector. The flexible lip and hinge allow the VRing to function even in the presence of a certain amount of run-out, eccentricity and shaft misalignment. V-Rings are made entirely of rubber without fabric or sheet metal reinforcement. They are, therefore, particularly easy to install. V-Rings can be stretched and,depending on size, installed over flanges, pulleys and bearing housings without costly dismantling.
V-Ring type A is the most common and available for shaft diameters in a wide range. In case a very firm hold on the shaft is required, V-Ring Type S is recommended, however these go only up to a shaft diameter of 200 mm.
技術尺寸
B+S V型圈TWVS系列其他常見型號：
B+S TWVS00220-N6T50
B+S TWVS00250-N6T50
B+S TWVS00250-VDT50
B+S TWVS00280-N6T50
B+S TWVS00300-N6T50
B+S TWVS00320-N6T50
B+S TWVS00350-N6T50
B+S TWVS00380-N6T50
B+S TWVS00400-N6T50
B+S TWVS00400-VDT50
B+S TWVS00450-N6T50
B+S TWVS00450-VDT50
B+S Ring NEW + ORIGINAL+ ONE YEAR WARRANTY
愛澤工業成立于2010年，定位于向先進制造工業提供高端制造技術和設備。代理經營世界先進的電氣自動化、機械與傳動、流體控制、儀器儀表、工具等產品。作為電氣，液壓以及氣動解決方案的合作伙伴，我們利用我們的全球協作團隊，為客戶提供先進解決方案，市場知識以及相關增值服務來幫助優化客戶的工作效率，提高可靠性和安全性，致力于成為工業產品和解決方案的優質渠道。
如果有任何關于B+S V型圈TWVS01900-N6T50的疑問，請隨時與我們溝通（021-31006702）。我們將盡全力解決您的問題。
If you have any question for B+S products, please feel free to dial 0086-21-3100 6702/ send request email to sales@ize-industries.com / browse our website:jjxdch.cn.
B+S V型圈TWVS01900-N6T50產品參數
