愛澤工業2024年9月部分到貨產品專題及庫存
——PH TOOL篇
如下為我司愛澤工業IZE_Industries本月到貨PH TOOL相關產品，歡迎致電索取樣本資料和產品信息。
PH TOOL校準塊BASIC4.5.SS
PH TOOL校準塊V15A2.A
PH TOOL校準塊BASIC4.5系列介紹
用于建立焊縫 UT 檢查的主要參考響應。測試塊包含三個側鉆孔，深度至少為 1.5，直徑為 3/32。貫穿厚度的孔位置為 ?、? 和 ?T。還包含兩個 EDM 凹槽，尺寸為 2%T 深 x 1/4 最大寬 x 1.0 最小長。
ASME 基本測試塊旨在代表實際組件，因此不具有大多數通用測試塊（如 IIW 或 DSC）上的光滑掃描表面。相反，基本測試塊的所有表面都經過噴砂處理，以創建更符合真實檢查條件的粗糙表面紋理。
尺寸：? 厚 x 6? 寬 x 6.0 長
可選配木制儲物箱
Used for establishment of primary reference responses for UT examination of welds. Block contains three side-drilled holes at 1.5 deep minimum at 3/32 diameter. Hole locations through the thickness are ?, ?, and ?T. Also contains two EDM notches measuring 2%T deep x 1/4 max wide x 1.0 long min.
ASME Basic Calibration Blocks are intended to be representative of actual components, and therefore do not have the smooth scanning surfaces found on most general-purpose test blocks like the IIW or DSC. Instead, our Basic Calibration Blocks are media blasted on all surfaces to create a rough surface texture that is more characteristic of real-world inspection conditions.
Dimensions: ? thick x 6? wide x 6.0 long
Fitted wooden storage case optional
PH TOOL校準塊V15A2系列介紹
用于在實驗室和現場條件下校準超聲波探傷設備。
此塊的版本包括半徑 100 毫米、1.5 毫米和 50.0 毫米孔、雕刻參考標記刻度和零點處的兩個可選插槽，可提供 100 毫米范圍內的間隔校準信號。
此塊不與新的 EN 12223/ISO 2400 測試塊 No. 1（也稱為 K1 塊）混淆，后者類似，但包含 3.0 毫米通孔而不是 1.5 毫米孔。
? 1018 鋼鍍鎳
? 尺寸：300 毫米 x 100 毫米 x 25 毫米
? 可選配木質收納盒或考杜拉袋
For calibrating ultrasonic flaw detection equipment in both laboratory and on-site conditions.
The version of this block includes a 100mm radius, 1.5mm and 50.0mm holes, engraved reference mark scales, and two optional slots at the zero point which provide calibrating signals at intervals of 100mm range.
This block is not to be confused with the new EN 12223/ ISO 2400 Calibration Block No. 1 (also called the K1 block,) which is similar but contains a 3.0mm through-hole rather than a 1.5mm hole.
? 1018 Steel is Nickel Plated
? Dimensions: 300mm x 100mm x 25mm
? Fitted wooden storage case or cordura pouch optional
PH TOOL校準塊ASTM8系列介紹
一組八個平底孔塊，用于通過比較信號響應來確定缺陷尺寸和回波幅度之間的關系。
所有塊的金屬行進距離為 3.000 英寸，F(xiàn)BH 直徑范圍從 #1 (1/64) 到 #8 (8/64)。符合 ASTM E127-19（現在涵蓋所有材料，而不僅僅是鋁。）包括我們的 NIST 可追溯認證報告、超聲波檢查報告和響應圖以及認證材料測試報告。
尺寸：FBH 直徑為 1/64、2/64、3/64、4/64、5/64、6/64、7/64 和 8/64。塊直徑為 2.0 英寸
注意：7075-T6 鋁版默認為軟陽極氧化，染成黑色。請注意，這種軟陽極涂層不適合永久浸泡在硬水中。如果您計劃將塊永久浸泡或長期浸泡在水中，請與 PH Tool 銷售人員討論密封硬陽極涂層的選項。
Set of eight flat-bottom hole blocks used to determine the relationship between flaw size and echo amplitude by comparing signal responses.
Metal travel distance is 3.000” for all blocks, and FBH diameter ranges from #1 (1/64) to #8 (8/64). In accordance with ASTM E127-19 (now encompassing all materials, not just aluminum.) Includes our NIST traceable certification report, ultrasonic inspection report and response plot, and the certified material test report.
Dimensions: FBH diameters are 1/64, 2/64, 3/64, 4/64, 5/64, 6/64, 7/64, and 8/64. Block diameter is 2.0"
Note: 7075-T6 Aluminum version is soft-anodized, dyed black color by default. Note that this soft anodic coating is not suitable for permanent immersion in hard water. If you plan to keep blocks permanently immersed or immersed long-term in water, please discuss options for a sealed, hard anodic coating with PH Tool sales.
PH TOOL測試塊常用型號：
PH TOOL BASIC4.5.X
PH TOOL BASIC4.5.SS
PH TOOL BASIC4.5.AL
PH TOOL BASIC4.5.A51670
PH TOOL V15A2.T
PH TOOL V15A2.SSQ
PH TOOL V15A2.A
PH TOOL V15A2.CS
PH TOOL ASTM8.A
PH TOOL ASTM8.CS
PH TOOL ASTM8.SS
PH TOOL ASTM8.T
PH TOOL ASTM.0425.0600.CS
PH TOOL ASTM.0425.0600.A
PH TOOL IIW2.M4340
PH TOOL IIW2.I4340
PH TOOL IIW1 1018
PH TOOL IIW1 4340
PH TOOL IIW2 1010
PH TOOL IIW2 304
PH TOOL ASTM.0425.0600.CS
PH TOOL ASTM.0425.0600.A
PH TOOL ASTM.0300.0400.CS
PH TOOL ASTM.0300.0400.A
PH TOOL ASTM.0006.0275.CS
PH TOOL ASTM.0006.0275.A
PH TOOL ASTM.0300.0400.CS
如果您需要完整的PH TOOL的相關技術咨詢，請隨時致電愛澤工業（021-3100 6702），或者訪問網站jjxdch.cn,我們將盡全力解決您的問題。
If you have any question for PH TOOL，please feel free to dial 0086-21-3100 6702 or browse our website: jjxdch.cn.
IZE-industries
Contact Information：
Tel：0086-21-31006702 or 0086-21-35350722
Fax：0086-21-35350711
Mobile：0086-189 1750 1433
E-mail：sales@ize-industries.com
Website：jjxdch.cn
