閥門放大器工作原理
氣動放大器再現具有更高調節流量輸出壓力的低流量控制信號。它使用未調節的輸入壓力在流動和非流動條件下保持調節的輸出壓力。
A pneumatic air volume booster reproduce a low flow control signal with a higher regulated flow output pressure. It uses an unregulated input pressure to maintain a regulated output pressure under flowing and non-flowing conditions.
放大器連接到供應線和輸出管道。然而，它接收來自另一個設備的氣動控制信號，例如傳感器、閥門定位器或其他控制裝置。
The volume booster is connected to the supply line and the output plumbing. It receives a pneumatic control signal, however, from another device, such as a transducer, valve positioner or other control means.
該氣動信號控制進出增壓器的壓力，同時允許增壓器流過供應管線的最大體積。增壓器也可以稱為先導式調節器，因為您的控制或先導信號保持壓力控制。
This pneumatic signal controls the pressure into and out of the booster, while allowing the booster to flow the maximum volume of the supply line. Boosters may also be referred to as pilot-operated regulators, as your control or pilot signal maintains the pressure control.
氣動風量增壓器的調節輸出可以是以下任何一種：
氣動控制信號的直接再現
氣動控制信號的倍數
一小部分氣動控制信號
The regulated output of a pneumatic air volume booster can be any of the following:
A direct reproduction of the pneumatic control signal
A multiple of the pneumatic control signal
A fraction of the pneumatic control signal
體積增壓比是信號壓力到輸出壓力的倍增器或分壓器。例如，2:1 的比率意味著輸出壓力是信號壓力的 1/2。同樣，2:1 的比例將提供兩倍于信號壓力的輸出壓力。但是請注意，輸出壓力永遠不能超過增壓器的供應壓力。
The volume booster ratio is the multiplier or divider of signal pressure to output pressure. For example, a 2:1 ratio means output pressure is 1/2 the signal pressure. Similarly, a 2:1 ratio would provide output pressure twice the signal pressure. Note, however, the output pressure can never exceed the supply pressure to the booster.
信號壓力通常低于供氣壓力，因為控制裝置（閥門定位器、I/P 等）只能處理較低的供氣壓力。
Often the signal pressure is lower than the supply pressure because a control device (valve positioner, I/P, etc.) will only handle a lower supply pressure.
放大器用于提高沖程速度。如果需要精確的閥門控制，建議使用定位器。如果要使用體積增壓機進行開/關控制，則必須關閉增壓器上的整體旁路限制。
The volume booster is used to improve stroking speed. If precision valve control is required, the use of a positioner is recommended. If the volume booster is to be used for on/off control, the integral bypass restriction on the booster must be closed.
閥門放大器 Volume Booster
放大器用于氣動控制系統，將低流量信號傳遞為具有更大流量的信號。常見的配置是在輸入和輸出壓力之間提供 1:1 的比例，保持輸入和輸出信號的壓力相同。提供不同比例的產品。
A volume booster is used in a pneumatic control system to relay a low flow signal as one with greater flow volume. The common configuration is to provide a 1:1 ratio between the input and output pressure, keeping the input and output signals the same pressure. Products are available that deliver different ratios.
容積增壓器的一般用途是在低流量系統和高流量要求系統之間提供繼電器。
The general purpose of a volume booster is to provide a relay between a system with low flow volume and one with higher volume requirements.
一個典型的例子是氣動執行器。通過氣動信號線可用的流量可能不足以提供氣動致動器所需的響應速度。
A typical example is a pneumatic actuator. The flow available through the pneumatic signal line may be insufficient to deliver the response rate desired from the pneumatic actuator.
容積增壓器可控制獨立的空氣供應，通過在與控制信號相同的壓力下增加流量來解決這一難題。
A volume booster, with control over an independent air supply, solves this challenge with increased flow volume at the same pressure as the control signal.
放大器操作簡單。輸入信號向隔膜的一側施加力，向另一側施加輸出壓力。
Volume boosters are simple in operation. The input signal applies force to one side of a diaphragm, the output pressure to the other.
兩個施加壓力之間的不平衡將導致隔膜移動，改變閥門的位置和出口壓力，直到兩個力再次平衡。
An imbalance between the two applied pressures will cause the diaphragm to move, changing the position of the valve and the outlet pressure until the two forces are again in balance.
當設備安裝正確且供應空氣質量良好時，幾乎不需要維護。
Little maintenance is required when the units are properly installed and supply air is of good quality.
操作原理 Principle of Operation
圖1. Volume Booster 的剖面圖
Figure 1. Sectional View of Volume Booster
圖2. 機械安裝
Figure 2. Typical Installstions
請參閱圖 1 和圖 2，由于旁路限制，大輸入信號在增壓器輸入膜片上的寄存器變化比在執行器中更快。
Refer to figures 1 and 2. Because of the bypass restriction, large input signal changes register on the booster input diaphragm sooner than in the actuator.
輸入信號的大而突然的變化導致輸入信號和增壓器的輸出之間存在壓力差。
A large, sudden change in input signal causes a pressure differential to exist between the input signal and the output of the booster.
當發生這種情況時，隔膜移動以打開供氣口或排氣口，無論需要采取哪種行動來減小差值。
When this occurs, the diaphragms move to open either the supply port or the exhaust port, whichever action is required to reduce the differential.
該端口保持打開狀態，直到增壓器輸入和輸出壓力之間的差值回到增壓器的死區限制內。
The port remains open until the difference between the booster input and output pressures returns to within the deadband limit of the booster.
為穩定運行調整旁路限制后，幅度和速率變化較小的信號通過旁路限制進入執行器，而無需啟動增壓器操作。
With the bypass restriction adjusted for stable operation, a signal with small magnitude and rate changes passes through the bypass restriction and into the actuator without initiating booster operation.
供氣口和排氣口都保持關閉，防止不必要的空氣消耗和定位器繼電器可能的飽和。
Both supply and exhaust ports remain closed, preventing unnecessary air consumption and possible saturation of positioner relays.
好處 ：
快速響應，提高執行器行程速度
在高行程速度下保持正確的執行器定位
可調節旁通閥提供良好的操作靈敏度
高穩定性，允許正常的慢速執行器響應慢速信號變化
能夠使用高壓工廠供氣
提供不同的放大器尺寸，以適應各種執行器尺寸
主內部供氣閥，帶軟閥座插件，用于緊密關閉
Advantages :
Quick response with increeased actuator stroking speeds
Maintains correct actuator postioning at high stroking speeds
Adjustable by pass valve provides good operational sensitivity
High stability which allow normal slow actuator response to slow signal changes
Capable of using high pressure plant air supply
Different Booster sizes available to suit wide range of actuator sizes
Main internal air supply valve with Soft seat insert for tight shut off
聲明：
- 文章轉載自網絡，如有侵權，請聯系刪除！
- 如有偏頗，歡迎指正！
